PARTS COMPATIBILITY FOR ARO10 Please help

All about performance,service,spare parts

Moderator: UMMM461

Post Reply
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

SorinTVY wrote:check beering for wear, ""piting", no shaft play(feel by hand) are not allowed ,when the ghear box was "siel'd",

the rolers on the triax front shaft hosing , if no play exisst, end the triax is not mooving inside the housing, just cleen the old gres, the conexion shaft betwin the weel end diferential , musn't be play betwin ,the sfat..end the weel part -housing-rollers., if ar worn owt, must bee made new roollers, (hard steel like sprochets in the geearboxes- ), theat all,...

ruber housing for the shaf, renault 12 will fit, but deepends,.. you chan use universal ones,

there was no play in the gear box,
i`ve oppened the front axles they look ok. no play or wearing off. i will change the rubbers and assamlbe them again.

Sorin i`ve read this post.
http://www.aro4x4.net/smf/viewtopic.php ... &start=105
but i cant understand about the shocks.. dacia Oem but from which dacia.. which model which year.. i would like to buy them but in the shop they asked me from which dacia..

User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

after cleaning i have found out that the front axle is damaged on the place where it fits the bearing... can you tell me if there are front axles that fit the aro or i will have to repair it?
User avatar
Soryn
Membru legendar
Membru legendar
Posts: 3367
Joined: 13 Apr 2008, 18:38
Location: Constanta

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by Soryn »

make picture, dacia/ R12, fits but the weel part it's smaler, end short.!
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

hey guys,
i got the new gear after many months in production..
i`ve finished assembling the transfer case and i`m ready to attach it to the gearbox as soon as i find that nut from VW transporter to bolt it all together.
i need information about the oil that should go in the transfer box, gear box and deferentials.

i`ll upload some photos later :)

User avatar
Soryn
Membru legendar
Membru legendar
Posts: 3367
Joined: 13 Apr 2008, 18:38
Location: Constanta

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by Soryn »

User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

10x sorin :)
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

icemann wrote:10x sorin :)
Sorin Do you know if there is another car that fits the same stabilizators and the rods that are connected to the front wheels.
the rubbers are destroyed and i cant find the rubbers for aro.
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

i need these parts.. how to search them?
User avatar
Soryn
Membru legendar
Membru legendar
Posts: 3367
Joined: 13 Apr 2008, 18:38
Location: Constanta

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by Soryn »

2x ruber busch with 19 mm hole
in romania is difficult to find ruber parts for the car's becouse rubber factori's are dead closed
i thinck wil fit some buschins from other car, but we must serch by the pictures end schematic drowiing .
is hard but not catastrofic.
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

This is the progress so far..
i`ve bought 15inch rims and 205 70 15 tires.. i still think they are small. the front looks little bit lower but i need to measure it on a flat surface..
now i need to put the brakes bleed them, and work in the interior..
also im without front diff i`ll be only with rear for some time.. and insert the front diff later..
DSC_0075[1].jpg
DSC_0079[1].jpg
DSC_0077[2].jpg
for the blinkers i`ve made parts from polyester and bought land rover lights.. the original are broken and finding new in here is impossible
You do not have the required permissions to view the files attached to this post.
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

sorin i`m trying to fix the brakes but i have problems with the main cylinder or break pump... i need schematics i think i made mistake with the rubber parts in the pump..
i need some assembly schematics in order to fix it..
thanks..
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

i`ve bought new break pump from R4 R11 and i fitted it.. it works ok.. i now have break system..
but i still would like schematics for the old one.. i would like to fix it and keep it for spare parts..

pictures later this day
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

Here are some progress pics.
i desided to create side blinkers from fiberglass.

this is just to see how it will look.
1.jpg
than i created models from gips.this is radicol material for gluing drywall panels.
2.jpg
than i created negative mold from the same material
3.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

This is the part from the negative mold.
4.jpg
after some cutting and rough sanding and gluing to the black cover for the headlights.
5.jpg
after covering it with kit.
6.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
icemann
Membru
Membru
Posts: 188
Joined: 13 Jul 2012, 18:47
Location: Skopje, Macedonia

Re: PARTS COMPATIBILITY FOR ARO10 Please help

Post by icemann »

This is with sanded kit and lights fitted.. ready for paint.
7.jpg
this is covered with filler.
8.jpg
and final product.
9.jpg
You do not have the required permissions to view the files attached to this post.

Post Reply